Looking for an industrial heat pump in Ahmedabad? The best choice depends on your process, not on a brand name. So this page explains how to pick a heat pump for industry, and how Kalyan Engineering can help. We make MAGMA heat pumps in Dehgam, on the Naroda Dehgam Road that leads towards Ahmedabad’s Naroda industrial estate.

Call or WhatsApp +91 98987 52420, or send your requirement.

What makes the best heat pump for industry

Check these five points before you choose.

The temperature you need

Every process has a target temperature. However, a heat pump works best when the gap between its heat source and that target is small. The WBCSD notes that a bigger temperature lift lowers efficiency. For this reason, ask your team for the lowest temperature the process can safely use.

Hours of use

Plants that need hot water for long, steady hours gain the most. Because the unit runs often, the energy saving builds up day after day.

Climate in Ahmedabad and your industrial heat pump

The US Department of Energy says any air-source heat pump works more efficiently in a warm climate. Ahmedabad has a long hot season. As a result, an industrial heat pump in Ahmedabad suits local conditions well.

Your existing boiler or heater

Many plants keep a boiler for high-temperature steps. In this case, a heat pump can supply the lower-temperature hot water and reduce the boiler load. We discuss this with you before we recommend anything.

Installation and service

A heat pump runs for years, so support matters. Therefore, choose a supplier with an installation and service team, as we offer through our Installation and Services page.

Industries in Ahmedabad that use hot water daily

GIDC set up the Naroda, Odhav and Vatva industrial estates in 1968 on the eastern edge of Ahmedabad. An urban study notes that the Naroda estate hosts chemical and textile industries. It also hosts national and multinational companies.

Gujarat as a whole leads in chemicals, pharmaceuticals, dairy, textiles and engineering, according to IBEF. In addition, GIDC describes its Sanand estate as a base for automobile and engineering units. The estate lies about 30 to 35 km from Ahmedabad.

Plants in these sectors use hot water for washing, rinsing, cleaning and process steps. For example, our application list includes dairy, pharmaceutical, laundry and automobile units, plus hospitals and hotels.

Heat pump or boiler? A realistic view

A heat pump is not right for every step. Efficiency is highest at low and medium temperatures. For example, the WBCSD reports that commercial use becomes limited above roughly 150°C. So if your process needs high-temperature steam, a boiler may stay.

However, hot water for washing, rinsing and pre-heating is often a good fit. We will tell you honestly when a heat pump is not the right tool.

Your industrial heat pump in Ahmedabad from MAGMA

Our MAGMA Semi-Commercial and Commercial heat pumps give higher protection and capacity for business use. For an industrial heat pump in Ahmedabad, we start with your temperature and daily volume. Then we confirm the right model, install it and support it.

You deal directly with Kalyan Engineering at GIDC Dehgam. We also supply Maharashtra, Goa and Rajasthan.

What to send us for an industrial heat pump in Ahmedabad

Please send these details by phone, WhatsApp or the Connect With Us.

• What the hot water is used for
• The temperature you need
• Daily volume in litres and hours of use
• How you heat water today
• Power supply at your site
• Your plant location in Ahmedabad

We will then reply with a recommendation for your process. Our address is 305 G.I.D.C, Nr. Nehru Chowkdi, Naroda Dehgam Road, Dehgam, Gandhinagar (Dist) – 382305, Gujarat.

FAQs about industrial heat pumps in Ahmedabad

Which industrial heat pump is best for my plant in Ahmedabad?

It depends on your process. The key factors are the temperature, the daily volume and the hours of use. So send these details to us, and we will recommend a MAGMA model.

What temperature can your heat pump deliver?

The answer depends on the model. Tell us the temperature your process needs, and we will confirm which MAGMA model can deliver it.

Can a heat pump replace my boiler?

Sometimes. A heat pump can supply hot water for washing and pre-heating. However, high-temperature steam may still need a boiler, so we discuss a combined setup when it makes sense.

Do heat pumps work well in Ahmedabad’s heat?

Yes, warm weather helps. The US Department of Energy says air-source heat pumps work more efficiently in a warm climate. We still size each system for your site.

Do you install and service the heat pump?

Yes. Kalyan Engineering provides installation and service. You can also read more on our Installation and Services page.